How To Succeed At Slurry Pumping
Optimal transfer of two-phase solid-liquid flow (slurry flow) has long been a major industrial challenge. Slurry pumps are among the most common types of centrifugal pumps used to deal with this transfer issue. The approach of improving slurry pumps and consequently increasing the efficiency of a flow transmission system requires overcoming the effects of slurry flow such as the reduction in head, efficiency, and wear. This study attempts to investigate the changes in the pump head by modifying the slip factor distribution in the impeller channel. For this purpose, the effect of splitter blades on slip factor distribution to improve the pump head was investigated using numerical simulation tools and validated based on experimental test data. Next, an optimization process was used to determine the characteristics of the splitter (i.e., length, number, and environmental position of the splitter) based on a combination of experimental design methods, surface response, and genetic algorithm. The optimization results indicate that the splitters were in a relative circumferential position of 67.2% to the suction surface of the main blade. Also, the optimal number and length of splitter blades were 6 and 62.8% of the length of the main blades, respectively. Because of adding splitter blades and the reduction in the flow passage, the best efficiency point (BEP) of the slurry pump moved toward lower flow rates. The result of splitter optimization was the increase in pump head from 29.7 m to 31.7 m and the upkeep of efficiency in the initial values.
The effect of solids on a centrifugal horizontal slurry pump performance is a major concern to the design of slurry transportation system. In the present study, the multiphase modeling of centrifugal slurry pump is performed using two models, Mixture and Eulerian-Eulerian multiphase. Sliding mesh approach is employed for unsteady simulation of the pump. The accuracy of the simulations is ascertained by comparing the performance characteristics of the pump obtained numerically and experimentally. Experimental results are obtained by measurements in a pilot plant test rig with three different mean size sand particulate slurries. The Eulerian-Eulerian multiphase model predicted the effect of the solids on pump performance close to the experimental results as compared to Mixture model. The obtained accuracy with Eulerian-Eulerian model for predicting the effect of solids on head and efficiency is around ±2% and ±3%, respectively. The predicted results using Eulerian-Eulerian model confirm that the head and efficiency of the pump decrease with the increase in particle size and concentration. The particles of high specific gravity show less reduction in head and efficiency of the pump. Further, the effect of variation in particle size and concentration on the flow field in the impeller and casing has also been analyzed at best efficiency point operation. Non-homogeneous suspension of particles inside the blade channels and casing passages is examined. The particulate concentration is observed higher near the impeller back shroud, pressure side of the blades, and non-suction side of the casing as compared to other locations.
Plants often must handle slurries in applications ranging from processing to wastewater treatment. Dealing with such mixtures of liquid and solids is challenging and difficult. Some key elements in slurry pumping are the size and nature of the solids in the liquid and the kind of the abrasive wear they cause. Another is the corrosiveness of the liquid or the mixture.
Sites frequently rely on centrifugal pumps for slurry services. These pumps (and their associated piping systems) need special provisions that call for a detailed knowledge of the solid and slurry properties to prevent wear, corrosion, erosion and other adverse effects such as settling of the solids. Specifying the optimum combination of speed, geometry and materials requires properly balancing often conflicting pump priorities; this demands consideration of stable operation, maximum wear life, operational flexibility and minimal energy consumption.
In this article, we’ll cover practical guidelines and rules for centrifugal pumps for slurries. We’ll also discuss key operational features, material selection and other considerations.
Tailored Pumps
Horizontal centrifugal pumps usually are used for slurry services, although vertical and other types of pumps are favored for some specific applications. Centrifugal pumps for handling slurries have features tailored to the particular service that reflect the corrosive or abrasive nature of the slurry and the solids concentration. These may include choice of materials, use of liners and even different driver sizing.
